EP brand replacement gearbox for woods rotary gearbox

EP brand alternative gearbox for woods rotary gearbox

NEW forty HP GEARBOX Clean Input 1 3/8 12 spline output Interchangable with market well-liked measurement i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE A lot of More

Features
(one) brand name new forty five horse electrical power shearpin gearbox. This gearbox fits many different can make of 4′,5′ and some 6′ rotary cutters. I offer a great deal of these boxes every year for a number of various purposes and carry ALL Alternative Elements for this box, but ideally you will not likely have to worry about that.
Right here are the specs on the box:
*forty five horse electrical power gearbox
*Normal 1-3/eight” clean input shaft(in which the pto shaft hooks on). The pto shaft is held on by a one/two shearbolt.
*duration of the input shaft out of the gearbox is three” extended
*bolt hole sample for mounting is on the corners, 4-3/4 centre of hole to center of hole. It requires a five/8″ bolt.
*twelve splined output shaft(where the blade carrier hooks up on the base)
*1-9/sixteen outdoors measurement more than the output shaft splines- from the foundation of the output cap to the stop of the splines is 2-three/4″ long- all round duration of the output shaft is four-one/two” extended.
*normally takes a 1″ threaded castle nut and a carter essential on the bottom of the output shaft to safe blade pan(NUT is integrated – – BLADE PAN IS NOT!!)
*total peak of the box from the prime of the mower deck to the best of the box is nine-one/two”
This is a fairly hefty merchandise (forty seven lbs.) so freight is not low cost, but we do not make anything off of freight, what ever ups costs us we demand you.
forty HP
one:one:47 Ratio
1-3/eight” Clean Enter Shaft with Shear Pin Gap
one-1/2″ twelve-Spline Ouput Shaft
Bolt Sample: 6-1/two” (four) five/8″ Holes, five” Middle Hole Needed for Shaft Assembly
The Enter and Output Shafts Can’t be Acquired Serparately.
They are Marketed as a kit.
The package involves the adhering to elements: input shaft, input equipment, output shaft, output gear.
The Shaft Kit Are not able to Be Separated.

EP manufacturer substitute gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or normally executing improperly? You have occur to the appropriate place.

Read through below for the most common issues with rotary cutter gearboxes and their options (from rapid and filthy, to professional).

Leaking Bottom Seal:
If you’ve wrapped some baling or fencing wire all around your output shaft and blown the seal, the expert issue to do is to change the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing houses can purchase you up a generic double-lip seal that will get you back again up-and-operating. If not, give us a phone and we can support you form out what you need to have.
A dental decide is the best way to get rid of the outdated seal before urgent in the new 1.
If you might be blessed ample to have a gradual-leak, the quick and filthy technique is to run automotive-variety grease in the gearbox right up until the new seal comes in. Be confident to check out and add grease much more usually than you would with oil, as this is NOT a specialist fix.

Broken Output Shaft:
Uh oh. You strike some thing that did not shift. The excellent information is that the output shaft on most gearboxes is relatively straightforward to replace. The undesirable information is… it truly is rarely an isolated failure.
The first point to do is to just take apart your gearbox and evaluate the complete extent of the injury. If it is genuinely just the output shaft, you should be in a position to alter it out, no difficulty. The output shafts start off at about $70 and go up in value based on the measurement of the gearbox.
Even so, in most instances, the bearings ($twenty/ea), seals ($ten/ea) and gear-set ($70) will also usually take a beating. If you’re unlucky, the output cap ($eighty) will also experience some hurt.
In this scenario, it is normally less costly to replace the gearbox. Compare the price of parts to the expense of an total, new, warrantied gearbox. At times, even experts have to know when to call it a day.

I Want to Alter my Input Shaft:
If you are tired of altering shear pins or seeking again and seeing that your mower hasn’t been slicing, you might want to put in a slip-clutch pto shaft (Indeed, we sell people too).
This normally calls for putting in a 540-style, 6-spline input shaft ($85) on your mower’s gearbox.
Fortunate for you, we did a publish-up on our weblog. It really is referred to as “How to alter the enter shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound type-of equivalent above-the-cellphone. The best thing to do is to disassemble your gearbox and get a search at the gears and bearings. The problem will typically existing alone in the way of damaged/missing equipment tooth, toasted gears (like that photograph on our residence page), or blown bearings.
If everything appears standard, try adjusting the gear-mesh. This is carried out with the mylar “gaskets” that sit among the primary gearbox circumstance and the input/output caps. Try incorporating or getting rid of some of these spacers till your gears have about 1/8″-one/four” of totally free engage in. Professionals can order replacements ($one-two) in different thicknesses, but we advise the swift and soiled strategy of reducing your possess out of a sheet of mylar.
Do not overlook to re-seal the gearbox with RTV following you’ve got discovered the proper blend. Even however they are named “gaskets”, they won’t seal your gearbox on their personal.

If you would certainly such as even more information on Rotary Harrows gearbox, please don’t be reluctant to call us.

Tags:

Find us

Ep Screw Jack Co., Ltd.

Mail: [email protected]

As one of leading manufacturers, suppliers and exporters of mechanical products in China, We offer reducers, sprockets, industrial and conveyor chain, belts, pulleys, gears, racks, gearboxes, motors, PTO Shafts, taper lock Bushing, vacuum Pumps, screw air compressors and many other products. Please contact us for details.

Recent Posts